Lawn Care Choosing Between Portable or In-Ground Sprinklers Article / Updated 07-05-2023 Choosing an irrigation system is about convenience, efficiency, and water conservation. Deciding on portable sprinklers or an in-ground irrigation system basically comes down to cost versus time and convenience. Portable sprinklers aren’t necessarily the most efficient system to use to water your grass. You know — hooking up the oscillating or impulse sprinklers, dragging the hose all over the lawn, watching the clock, and trying to remember when you should move the sprinkler to a different part of the lawn. Because your lawn should be watered in the morning, are you willing to get up in predawn hours to start the process? Then there’s the question of how you’re going to drag that sprinkler over your new lawn. You’ll turn that nice smooth ground into the lunar surface. Portable sprinklers also can be difficult to adjust and point so that the lawn gets evenly watered without wetting the sidewalk or street. The goal isn’t to turn the street gutters into rivers. Portable sprinklers water areas unevenly, and a lot of the water gets lost to evaporation as the sprinklers throw the water up into the air to fling it far and wide. The secret to getting a great looking lawn while conserving precious water is to evenly moisten the root zone without filling the street gutters. Even if you have the best lawn soil in the world, soil can absorb water only at a certain rate. If you deliver water faster than the soil can absorb it, you get runoff — a big waste. Permanent, in-ground irrigation systems usually send up light misty sprays of water that you can aim carefully. The soil absorbs water slowly over a longer period of time. You get more bang for your buck because you use less water to get a better-looking lawn. Don’t forget! Your time is valuable, too. With an automatic timer controller installed on your irrigation system, you can water your lawn well and wisely even when you aren’t home. You can even install moisture-sensoring devices that withhold watering during times when rainfall is doing an adequate job. The only drawback to an in-ground irrigation system is that it can be rather expensive — more expensive if you hire a professional to install it and less expensive if you do it yourself. But a permanent in-ground system, properly installed and maintained, is an asset for you and your home’s value, just like a new bathroom or a sun porch. If you need to water your lawn and you can afford it, an in-ground irrigation system is the best choice for you. You may save a little money on your water bill, and you can definitely increase the value of your real estate. In addition, your lawn will look lovely. Naturally, if you live in an area where summer rainfall is plentiful and you need to water your lawn only a couple times during dry spells, a permanent irrigation system may not make sense. The same is true if you have a small lawn. View Article

Lawn Care How to Mow a Lawn the Right Way Article / Updated 02-07-2023 How to mow a lawn or grass the right way is one of the most important practices in keeping your lawn healthy. Grasses are like most plants — if you clip off the growing points (for grass, it's in the crown, where the new leaves develop), the plants branch out and become denser, which in this case, turns thousands of individual grass plants into a tightly woven turf or a lawn. If you didn't mow at all, your yard would look more like a prairie than a lawn. But the mere act of mowing isn't what makes a lawn look good. Mowing height and mowing frequency determine how healthy and attractive your lawn looks. After all, cutting a lawn is stressful for the grass. The leaves make the food for the roots — and how would you like it if someone kept cutting off your food? Height does count when you mow a lawn Most grasses have a range of recommended mowing heights. Stay at the upper end of that range when the lawn is under stressful conditions, such as hot weather or drought, or if you have a shady lawn. In cooler weather, you can cut the grass a little lower. Follow the one-third rule. For a thriving lawn, never cut away more than one-third of the grass blade in any one mowing. If the grass "gets ahead of you" because of wet weather or your busy schedule, move up the cutting height of your mower to the highest possible setting and mow. If clippings are too long and heavy, even at that cutting height, catch them with the bagging unit or clean up after mowing with a leaf rake. Then move the cutting height back to your normal range and cut the lawn again a few days after that first mowing. Table 1 shows suggested mowing heights for different grass types. Table 1: Ideal Mowing Heights Bent grass1/4 to 1 inchHow to mow a lawn or grass the right way is one of the most important practices in keeping your lawn healthy. Grasses are like most plants — if you clip off the growing points (for grass, it's in the crown, where the new leaves develop), the plants branch out and become denser, which in this case, turns thousands of individual grass plants into a tightly woven turf or a lawn. If you didn't mow at all, your yard would look more like a prairie than a lawn. But the mere act of mowing isn't what makes a lawn look good. Mowing height and mowing frequency determine how healthy and attractive your lawn looks. After all, cutting a lawn is stressful for the grass. The leaves make the food for the roots — and how would you like it if someone kept cutting off your food?Height does count when you mow a lawnMost grasses have a range of recommended mowing heights. Stay at the upper end of that range when the lawn is under stressful conditions, such as hot weather or drought, or if you have a shady lawn. In cooler weather, you can cut the grass a little lower.Follow the one-third rule. For a thriving lawn, never cut away more than one-third of the grass blade in any one mowing. If the grass "gets ahead of you" because of wet weather or your busy schedule, move up the cutting height of your mower to the highest possible setting and mow. If clippings are too long and heavy, even at that cutting height, catch them with the bagging unit or clean up after mowing with a leaf rake. Then move the cutting height back to your normal range and cut the lawn again a few days after that first mowing.Table 1 shows suggested mowing heights for different grass types.Table 1: Ideal Mowing HeightsEdging and trimming are the finishing touches of mowing, kind of like getting a shave after you've had a haircut. Edging and trimming are pretty close to being the same thing. Some tools are called edgers because they're designed to trim the lawn along a hard surface like a driveway or sidewalk. Edgers cut a nice clean edge, but leave some dirt and grass debris that you need to clean up. On the other hand, you can use trimmers anywhere — along a hard surface, in tight spaces, next to planting beds, and so on. Trimmers also leave some clippings on paths and driveways that you need to sweep up.Never put grass clippings in a plastic bag and send them off to the dump. (In some areas, sending grass clippings to the dump is illegal.) Grass clippings are valuable organic matter, chock-full of nitrogen and other nutrients. As long as you mow often enough to remove no more than one third of the grass blade, the easiest thing to do is just to leave clippings on the lawn. The pieces break down quickly and reduce the amount of fertilizer you have to use by as much as 25 percent. And research has proven that the clippings don't cause thatch to build up.Lawn mowing safety when you mow a lawnEvery year, hundreds, maybe even thousands, of people get injured when using lawn mowers. Power lawn mowers can be dangerous even when used properly. Be proactive when it comes to safety and follow these tips to avoid injuries: Know the equipment. Read the owner's manual. Become familiar with all the safety features and don't disconnect any of them. Keep all nuts and bolts properly tightened. Never pull a walking mower. Check the lawn before mowing and wear proper clothing. Pick up any rocks or debris. Heavy shoes and long pants provide the best protection from flying debris. If you're using a reel mower, don't wear loose clothing. Protect your hearing. Doing yard work can get pretty noisy. In addition to the lawn mower, high-decibel noise comes from trimmers, edgers, and blowers. Use earplugs or earmuff-type hearing protection. Keep pets and children away from the lawn as you mow. Don't let children operate a lawn mower unless they're strong enough, responsible, and understand all the operating and safety features. Even then, supervise them. Never give a young child a ride on a ride-on mower. Sudden stops, flying objects, or an excited child can spell disaster. Be careful when fueling. Stop the mower and let the engine cool for 10 minutes before fueling. Never fill the tank with the mower on the lawn. Avoid spills by using a gas can with an adequate pouring spout. Clean up spills immediately and put the used rags in a covered metal can. (Gasoline-soaked rags are a fire hazard.) Turn off the mower. Never leave the mower running unattended, or work on a motor that is running. Turn off the power when you cross nongrass areas. Be careful on hills. Steep slopes are always dangerous because a mower can flip over or go out of control. Plant a ground cover other than turf in these areas. On gentle slopes, mow across the slope, not up and down. Use a walk-behind mower. Lawn mowers — a tree's worst enemyRepeatedly banging a mower against a tree trunk or whipping it senseless with a weed whip each week can seriously damage the bark and the sensitive tissues underneath. The damage can restrict the growth of young trees to the point where the base of the trunk is so weak and girdled that the tree just snaps off in the slightest wind.To protect the tree, leave a ring of grassless soil at least 3 feet wide around the trunk. Put in a nice brick or stone edging around the outside. Better yet, cover the open soil with a thick layer (3 to 6 inches deep) of organic mulch, such as compost or bark. (Keep the mulch a few inches away from the base of the tree.)How to mow a lawn or grass the right way is one of the most important practices in keeping your lawn healthy. Grasses are like most plants — if you clip off the growing points (for grass, it's in the crown, where the new leaves develop), the plants branch out and become denser, which in this case, turns thousands of individual grass plants into a tightly woven turf or a lawn. If you didn't mow at all, your yard would look more like a prairie than a lawn. But the mere act of mowing isn't what makes a lawn look good. Mowing height and mowing frequency determine how healthy and attractive your lawn looks. After all, cutting a lawn is stressful for the grass. The leaves make the food for the roots — and how would you like it if someone kept cutting off your food?Height does count when you mow a lawnMost grasses have a range of recommended mowing heights. Stay at the upper end of that range when the lawn is under stressful conditions, such as hot weather or drought, or if you have a shady lawn. In cooler weather, you can cut the grass a little lower.Follow the one-third rule. For a thriving lawn, never cut away more than one-third of the grass blade in any one mowing. If the grass "gets ahead of you" because of wet weather or your busy schedule, move up the cutting height of your mower to the highest possible setting and mow. If clippings are too long and heavy, even at that cutting height, catch them with the bagging unit or clean up after mowing with a leaf rake. Then move the cutting height back to your normal range and cut the lawn again a few days after that first mowing.Table 1 shows suggested mowing heights for different grass types.Table 1: Ideal Mowing HeightsEdging and trimming are the finishing touches of mowing, kind of like getting a shave after you've had a haircut. Edging and trimming are pretty close to being the same thing. Some tools are called edgers because they're designed to trim the lawn along a hard surface like a driveway or sidewalk. Edgers cut a nice clean edge, but leave some dirt and grass debris that you need to clean up. On the other hand, you can use trimmers anywhere — along a hard surface, in tight spaces, next to planting beds, and so on. Trimmers also leave some clippings on paths and driveways that you need to sweep up.Never put grass clippings in a plastic bag and send them off to the dump. (In some areas, sending grass clippings to the dump is illegal.) Grass clippings are valuable organic matter, chock-full of nitrogen and other nutrients. As long as you mow often enough to remove no more than one third of the grass blade, the easiest thing to do is just to leave clippings on the lawn. The pieces break down quickly and reduce the amount of fertilizer you have to use by as much as 25 percent. And research has proven that the clippings don't cause thatch to build up.Lawn mowing safety when you mow a lawnEvery year, hundreds, maybe even thousands, of people get injured when using lawn mowers. Power lawn mowers can be dangerous even when used properly. Be proactive when it comes to safety and follow these tips to avoid injuries: Know the equipment. Read the owner's manual. Become familiar with all the safety features and don't disconnect any of them. Keep all nuts and bolts properly tightened. Never pull a walking mower. Check the lawn before mowing and wear proper clothing. Pick up any rocks or debris. Heavy shoes and long pants provide the best protection from flying debris. If you're using a reel mower, don't wear loose clothing. Protect your hearing. Doing yard work can get pretty noisy. In addition to the lawn mower, high-decibel noise comes from trimmers, edgers, and blowers. Use earplugs or earmuff-type hearing protection. Keep pets and children away from the lawn as you mow. Don't let children operate a lawn mower unless they're strong enough, responsible, and understand all the operating and safety features. Even then, supervise them. Never give a young child a ride on a ride-on mower. Sudden stops, flying objects, or an excited child can spell disaster. Be careful when fueling. Stop the mower and let the engine cool for 10 minutes before fueling. Never fill the tank with the mower on the lawn. Avoid spills by using a gas can with an adequate pouring spout. Clean up spills immediately and put the used rags in a covered metal can. (Gasoline-soaked rags are a fire hazard.) Turn off the mower. Never leave the mower running unattended, or work on a motor that is running. Turn off the power when you cross nongrass areas. Be careful on hills. Steep slopes are always dangerous because a mower can flip over or go out of control. Plant a ground cover other than turf in these areas. On gentle slopes, mow across the slope, not up and down. Use a walk-behind mower. Lawn mowers — a tree's worst enemyRepeatedly banging a mower against a tree trunk or whipping it senseless with a weed whip each week can seriously damage the bark and the sensitive tissues underneath. The damage can restrict the growth of young trees to the point where the base of the trunk is so weak and girdled that the tree just snaps off in the slightest wind.To protect the tree, leave a ring of grassless soil at least 3 feet wide around the trunk. Put in a nice brick or stone edging around the outside. Better yet, cover the open soil with a thick layer (3 to 6 inches deep) of organic mulch, such as compost or bark. (Keep the mulch a few inches away from the base of the tree.)How to mow a lawn or grass the right way is one of the most important practices in keeping your lawn healthy. Grasses are like most plants — if you clip off the growing points (for grass, it's in the crown, where the new leaves develop), the plants branch out and become denser, which in this case, turns thousands of individual grass plants into a tightly woven turf or a lawn. If you didn't mow at all, your yard would look more like a prairie than a lawn. But the mere act of mowing isn't what makes a lawn look good. Mowing height and mowing frequency determine how healthy and attractive your lawn looks. After all, cutting a lawn is stressful for the grass. The leaves make the food for the roots — and how would you like it if someone kept cutting off your food?Height does count when you mow a lawnMost grasses have a range of recommended mowing heights. Stay at the upper end of that range when the lawn is under stressful conditions, such as hot weather or drought, or if you have a shady lawn. In cooler weather, you can cut the grass a little lower.Follow the one-third rule. For a thriving lawn, never cut away more than one-third of the grass blade in any one mowing. If the grass "gets ahead of you" because of wet weather or your busy schedule, move up the cutting height of your mower to the highest possible setting and mow. If clippings are too long and heavy, even at that cutting height, catch them with the bagging unit or clean up after mowing with a leaf rake. Then move the cutting height back to your normal range and cut the lawn again a few days after that first mowing.Table 1 shows suggested mowing heights for different grass types.Table 1: Ideal Mowing HeightsEdging and trimming are the finishing touches of mowing, kind of like getting a shave after you've had a haircut. Edging and trimming are pretty close to being the same thing. Some tools are called edgers because they're designed to trim the lawn along a hard surface like a driveway or sidewalk. Edgers cut a nice clean edge, but leave some dirt and grass debris that you need to clean up. On the other hand, you can use trimmers anywhere — along a hard surface, in tight spaces, next to planting beds, and so on. Trimmers also leave some clippings on paths and driveways that you need to sweep up.Never put grass clippings in a plastic bag and send them off to the dump. (In some areas, sending grass clippings to the dump is illegal.) Grass clippings are valuable organic matter, chock-full of nitrogen and other nutrients. As long as you mow often enough to remove no more than one third of the grass blade, the easiest thing to do is just to leave clippings on the lawn. The pieces break down quickly and reduce the amount of fertilizer you have to use by as much as 25 percent. And research has proven that the clippings don't cause thatch to build up.Lawn mowing safety when you mow a lawnEvery year, hundreds, maybe even thousands, of people get injured when using lawn mowers. Power lawn mowers can be dangerous even when used properly. Be proactive when it comes to safety and follow these tips to avoid injuries: Know the equipment. Read the owner's manual. Become familiar with all the safety features and don't disconnect any of them. Keep all nuts and bolts properly tightened. Never pull a walking mower. Check the lawn before mowing and wear proper clothing. Pick up any rocks or debris. Heavy shoes and long pants provide the best protection from flying debris. If you're using a reel mower, don't wear loose clothing. Protect your hearing. Doing yard work can get pretty noisy. In addition to the lawn mower, high-decibel noise comes from trimmers, edgers, and blowers. Use earplugs or earmuff-type hearing protection. Keep pets and children away from the lawn as you mow. Don't let children operate a lawn mower unless they're strong enough, responsible, and understand all the operating and safety features. Even then, supervise them. Never give a young child a ride on a ride-on mower. Sudden stops, flying objects, or an excited child can spell disaster. Be careful when fueling. Stop the mower and let the engine cool for 10 minutes before fueling. Never fill the tank with the mower on the lawn. Avoid spills by using a gas can with an adequate pouring spout. Clean up spills immediately and put the used rags in a covered metal can. (Gasoline-soaked rags are a fire hazard.) Turn off the mower. Never leave the mower running unattended, or work on a motor that is running. Turn off the power when you cross nongrass areas. Be careful on hills. Steep slopes are always dangerous because a mower can flip over or go out of control. Plant a ground cover other than turf in these areas. On gentle slopes, mow across the slope, not up and down. Use a walk-behind mower. Lawn mowers — a tree's worst enemyRepeatedly banging a mower against a tree trunk or whipping it senseless with a weed whip each week can seriously damage the bark and the sensitive tissues underneath. The damage can restrict the growth of young trees to the point where the base of the trunk is so weak and girdled that the tree just snaps off in the slightest wind.To protect the tree, leave a ring of grassless soil at least 3 feet wide around the trunk. Put in a nice brick or stone edging around the outside. Better yet, cover the open soil with a thick layer (3 to 6 inches deep) of organic mulch, such as compost or bark. (Keep the mulch a few inches away from the base of the tree.)How to mow a lawn or grass the right way is one of the most important practices in keeping your lawn healthy. Grasses are like most plants — if you clip off the growing points (for grass, it's in the crown, where the new leaves develop), the plants branch out and become denser, which in this case, turns thousands of individual grass plants into a tightly woven turf or a lawn. If you didn't mow at all, your yard would look more like a prairie than a lawn. But the mere act of mowing isn't what makes a lawn look good. Mowing height and mowing frequency determine how healthy and attractive your lawn looks. After all, cutting a lawn is stressful for the grass. The leaves make the food for the roots — and how would you like it if someone kept cutting off your food?Height does count when you mow a lawnMost grasses have a range of recommended mowing heights. Stay at the upper end of that range when the lawn is under stressful conditions, such as hot weather or drought, or if you have a shady lawn. In cooler weather, you can cut the grass a little lower.Follow the one-third rule. For a thriving lawn, never cut away more than one-third of the grass blade in any one mowing. If the grass "gets ahead of you" because of wet weather or your busy schedule, move up the cutting height of your mower to the highest possible setting and mow. If clippings are too long and heavy, even at that cutting height, catch them with the bagging unit or clean up after mowing with a leaf rake. Then move the cutting height back to your normal range and cut the lawn again a few days after that first mowing.Table 1 shows suggested mowing heights for different grass types.Table 1: Ideal Mowing HeightsEdging and trimming are the finishing touches of mowing, kind of like getting a shave after you've had a haircut. Edging and trimming are pretty close to being the same thing. Some tools are called edgers because they're designed to trim the lawn along a hard surface like a driveway or sidewalk. Edgers cut a nice clean edge, but leave some dirt and grass debris that you need to clean up. On the other hand, you can use trimmers anywhere — along a hard surface, in tight spaces, next to planting beds, and so on. Trimmers also leave some clippings on paths and driveways that you need to sweep up.Never put grass clippings in a plastic bag and send them off to the dump. (In some areas, sending grass clippings to the dump is illegal.) Grass clippings are valuable organic matter, chock-full of nitrogen and other nutrients. As long as you mow often enough to remove no more than one third of the grass blade, the easiest thing to do is just to leave clippings on the lawn. The pieces break down quickly and reduce the amount of fertilizer you have to use by as much as 25 percent. And research has proven that the clippings don't cause thatch to build up.Lawn mowing safety when you mow a lawnEvery year, hundreds, maybe even thousands, of people get injured when using lawn mowers. Power lawn mowers can be dangerous even when used properly. Be proactive when it comes to safety and follow these tips to avoid injuries: Know the equipment. Read the owner's manual. Become familiar with all the safety features and don't disconnect any of them. Keep all nuts and bolts properly tightened. Never pull a walking mower. Check the lawn before mowing and wear proper clothing. Pick up any rocks or debris. Heavy shoes and long pants provide the best protection from flying debris. If you're using a reel mower, don't wear loose clothing. Protect your hearing. Doing yard work can get pretty noisy. In addition to the lawn mower, high-decibel noise comes from trimmers, edgers, and blowers. Use earplugs or earmuff-type hearing protection. Keep pets and children away from the lawn as you mow. Don't let children operate a lawn mower unless they're strong enough, responsible, and understand all the operating and safety features. Even then, supervise them. Never give a young child a ride on a ride-on mower. Sudden stops, flying objects, or an excited child can spell disaster. Be careful when fueling. Stop the mower and let the engine cool for 10 minutes before fueling. Never fill the tank with the mower on the lawn. Avoid spills by using a gas can with an adequate pouring spout. Clean up spills immediately and put the used rags in a covered metal can. (Gasoline-soaked rags are a fire hazard.) Turn off the mower. Never leave the mower running unattended, or work on a motor that is running. Turn off the power when you cross nongrass areas. Be careful on hills. Steep slopes are always dangerous because a mower can flip over or go out of control. Plant a ground cover other than turf in these areas. On gentle slopes, mow across the slope, not up and down. Use a walk-behind mower. Lawn mowers — a tree's worst enemyRepeatedly banging a mower against a tree trunk or whipping it senseless with a weed whip each week can seriously damage the bark and the sensitive tissues underneath. The damage can restrict the growth of young trees to the point where the base of the trunk is so weak and girdled that the tree just snaps off in the slightest wind.To protect the tree, leave a ring of grassless soil at least 3 feet wide around the trunk. Put in a nice brick or stone edging around the outside. Better yet, cover the open soil with a thick layer (3 to 6 inches deep) of organic mulch, such as compost or bark. (Keep the mulch a few inches away from the base of the tree.)How to mow a lawn or grass the right way is one of the most important practices in keeping your lawn healthy. Grasses are like most plants — if you clip off the growing points (for grass, it's in the crown, where the new leaves develop), the plants branch out and become denser, which in this case, turns thousands of individual grass plants into a tightly woven turf or a lawn. If you didn't mow at all, your yard would look more like a prairie than a lawn. But the mere act of mowing isn't what makes a lawn look good. Mowing height and mowing frequency determine how healthy and attractive your lawn looks. After all, cutting a lawn is stressful for the grass. The leaves make the food for the roots — and how would you like it if someone kept cutting off your food?Height does count when you mow a lawnMost grasses have a range of recommended mowing heights. Stay at the upper end of that range when the lawn is under stressful conditions, such as hot weather or drought, or if you have a shady lawn. In cooler weather, you can cut the grass a little lower.Follow the one-third rule. For a thriving lawn, never cut away more than one-third of the grass blade in any one mowing. If the grass "gets ahead of you" because of wet weather or your busy schedule, move up the cutting height of your mower to the highest possible setting and mow. If clippings are too long and heavy, even at that cutting height, catch them with the bagging unit or clean up after mowing with a leaf rake. Then move the cutting height back to your normal range and cut the lawn again a few days after that first mowing.Table 1 shows suggested mowing heights for different grass types.Table 1: Ideal Mowing HeightsEdging and trimming are the finishing touches of mowing, kind of like getting a shave after you've had a haircut. Edging and trimming are pretty close to being the same thing. Some tools are called edgers because they're designed to trim the lawn along a hard surface like a driveway or sidewalk. Edgers cut a nice clean edge, but leave some dirt and grass debris that you need to clean up. On the other hand, you can use trimmers anywhere — along a hard surface, in tight spaces, next to planting beds, and so on. Trimmers also leave some clippings on paths and driveways that you need to sweep up.Never put grass clippings in a plastic bag and send them off to the dump. (In some areas, sending grass clippings to the dump is illegal.) Grass clippings are valuable organic matter, chock-full of nitrogen and other nutrients. As long as you mow often enough to remove no more than one third of the grass blade, the easiest thing to do is just to leave clippings on the lawn. The pieces break down quickly and reduce the amount of fertilizer you have to use by as much as 25 percent. And research has proven that the clippings don't cause thatch to build up.Lawn mowing safety when you mow a lawnEvery year, hundreds, maybe even thousands, of people get injured when using lawn mowers. Power lawn mowers can be dangerous even when used properly. Be proactive when it comes to safety and follow these tips to avoid injuries: Know the equipment. Read the owner's manual. Become familiar with all the safety features and don't disconnect any of them. Keep all nuts and bolts properly tightened. Never pull a walking mower. Check the lawn before mowing and wear proper clothing. Pick up any rocks or debris. Heavy shoes and long pants provide the best protection from flying debris. If you're using a reel mower, don't wear loose clothing. Protect your hearing. Doing yard work can get pretty noisy. In addition to the lawn mower, high-decibel noise comes from trimmers, edgers, and blowers. Use earplugs or earmuff-type hearing protection. Keep pets and children away from the lawn as you mow. Don't let children operate a lawn mower unless they're strong enough, responsible, and understand all the operating and safety features. Even then, supervise them. Never give a young child a ride on a ride-on mower. Sudden stops, flying objects, or an excited child can spell disaster. Be careful when fueling. Stop the mower and let the engine cool for 10 minutes before fueling. Never fill the tank with the mower on the lawn. Avoid spills by using a gas can with an adequate pouring spout. Clean up spills immediately and put the used rags in a covered metal can. (Gasoline-soaked rags are a fire hazard.) Turn off the mower. Never leave the mower running unattended, or work on a motor that is running. Turn off the power when you cross nongrass areas. Be careful on hills. Steep slopes are always dangerous because a mower can flip over or go out of control. Plant a ground cover other than turf in these areas. On gentle slopes, mow across the slope, not up and down. Use a walk-behind mower. Lawn mowers — a tree's worst enemyRepeatedly banging a mower against a tree trunk or whipping it senseless with a weed whip each week can seriously damage the bark and the sensitive tissues underneath. The damage can restrict the growth of young trees to the point where the base of the trunk is so weak and girdled that the tree just snaps off in the slightest wind.To protect the tree, leave a ring of grassless soil at least 3 feet wide around the trunk. Put in a nice brick or stone edging around the outside. Better yet, cover the open soil with a thick layer (3 to 6 inches deep) of organic mulch, such as compost or bark. (Keep the mulch a few inches away from the base of the tree.)How to mow a lawn or grass the right way is one of the most important practices in keeping your lawn healthy. Grasses are like most plants — if you clip off the growing points (for grass, it's in the crown, where the new leaves develop), the plants branch out and become denser, which in this case, turns thousands of individual grass plants into a tightly woven turf or a lawn. If you didn't mow at all, your yard would look more like a prairie than a lawn. But the mere act of mowing isn't what makes a lawn look good. Mowing height and mowing frequency determine how healthy and attractive your lawn looks. After all, cutting a lawn is stressful for the grass. The leaves make the food for the roots — and how would you like it if someone kept cutting off your food?Height does count when you mow a lawnMost grasses have a range of recommended mowing heights. Stay at the upper end of that range when the lawn is under stressful conditions, such as hot weather or drought, or if you have a shady lawn. In cooler weather, you can cut the grass a little lower.Follow the one-third rule. For a thriving lawn, never cut away more than one-third of the grass blade in any one mowing. If the grass "gets ahead of you" because of wet weather or your busy schedule, move up the cutting height of your mower to the highest possible setting and mow. If clippings are too long and heavy, even at that cutting height, catch them with the bagging unit or clean up after mowing with a leaf rake. Then move the cutting height back to your normal range and cut the lawn again a few days after that first mowing.Table 1 shows suggested mowing heights for different grass types.Table 1: Ideal Mowing HeightsEdging and trimming are the finishing touches of mowing, kind of like getting a shave after you've had a haircut. Edging and trimming are pretty close to being the same thing. Some tools are called edgers because they're designed to trim the lawn along a hard surface like a driveway or sidewalk. Edgers cut a nice clean edge, but leave some dirt and grass debris that you need to clean up. On the other hand, you can use trimmers anywhere — along a hard surface, in tight spaces, next to planting beds, and so on. Trimmers also leave some clippings on paths and driveways that you need to sweep up.Never put grass clippings in a plastic bag and send them off to the dump. (In some areas, sending grass clippings to the dump is illegal.) Grass clippings are valuable organic matter, chock-full of nitrogen and other nutrients. As long as you mow often enough to remove no more than one third of the grass blade, the easiest thing to do is just to leave clippings on the lawn. The pieces break down quickly and reduce the amount of fertilizer you have to use by as much as 25 percent. And research has proven that the clippings don't cause thatch to build up.Lawn mowing safety when you mow a lawnEvery year, hundreds, maybe even thousands, of people get injured when using lawn mowers. Power lawn mowers can be dangerous even when used properly. Be proactive when it comes to safety and follow these tips to avoid injuries: Know the equipment. Read the owner's manual. Become familiar with all the safety features and don't disconnect any of them. Keep all nuts and bolts properly tightened. Never pull a walking mower. Check the lawn before mowing and wear proper clothing. Pick up any rocks or debris. Heavy shoes and long pants provide the best protection from flying debris. If you're using a reel mower, don't wear loose clothing. Protect your hearing. Doing yard work can get pretty noisy. In addition to the lawn mower, high-decibel noise comes from trimmers, edgers, and blowers. Use earplugs or earmuff-type hearing protection. Keep pets and children away from the lawn as you mow. Don't let children operate a lawn mower unless they're strong enough, responsible, and understand all the operating and safety features. Even then, supervise them. Never give a young child a ride on a ride-on mower. Sudden stops, flying objects, or an excited child can spell disaster. Be careful when fueling. Stop the mower and let the engine cool for 10 minutes before fueling. Never fill the tank with the mower on the lawn. Avoid spills by using a gas can with an adequate pouring spout. Clean up spills immediately and put the used rags in a covered metal can. (Gasoline-soaked rags are a fire hazard.) Turn off the mower. Never leave the mower running unattended, or work on a motor that is running. Turn off the power when you cross nongrass areas. Be careful on hills. Steep slopes are always dangerous because a mower can flip over or go out of control. Plant a ground cover other than turf in these areas. On gentle slopes, mow across the slope, not up and down. Use a walk-behind mower. Lawn mowers — a tree's worst enemyRepeatedly banging a mower against a tree trunk or whipping it senseless with a weed whip each week can seriously damage the bark and the sensitive tissues underneath. The damage can restrict the growth of young trees to the point where the base of the trunk is so weak and girdled that the tree just snaps off in the slightest wind.To protect the tree, leave a ring of grassless soil at least 3 feet wide around the trunk. Put in a nice brick or stone edging around the outside. Better yet, cover the open soil with a thick layer (3 to 6 inches deep) of organic mulch, such as compost or bark. (Keep the mulch a few inches away from the base of the tree.)How to mow a lawn or grass the right way is one of the most important practices in keeping your lawn healthy. Grasses are like most plants — if you clip off the growing points (for grass, it's in the crown, where the new leaves develop), the plants branch out and become denser, which in this case, turns thousands of individual grass plants into a tightly woven turf or a lawn. If you didn't mow at all, your yard would look more like a prairie than a lawn. But the mere act of mowing isn't what makes a lawn look good. Mowing height and mowing frequency determine how healthy and attractive your lawn looks. After all, cutting a lawn is stressful for the grass. The leaves make the food for the roots — and how would you like it if someone kept cutting off your food?Height does count when you mow a lawnMost grasses have a range of recommended mowing heights. Stay at the upper end of that range when the lawn is under stressful conditions, such as hot weather or drought, or if you have a shady lawn. In cooler weather, you can cut the grass a little lower.Follow the one-third rule. For a thriving lawn, never cut away more than one-third of the grass blade in any one mowing. If the grass "gets ahead of you" because of wet weather or your busy schedule, move up the cutting height of your mower to the highest possible setting and mow. If clippings are too long and heavy, even at that cutting height, catch them with the bagging unit or clean up after mowing with a leaf rake. Then move the cutting height back to your normal range and cut the lawn again a few days after that first mowing.Table 1 shows suggested mowing heights for different grass types.Table 1: Ideal Mowing HeightsEdging and trimming are the finishing touches of mowing, kind of like getting a shave after you've had a haircut. Edging and trimming are pretty close to being the same thing. Some tools are called edgers because they're designed to trim the lawn along a hard surface like a driveway or sidewalk. Edgers cut a nice clean edge, but leave some dirt and grass debris that you need to clean up. On the other hand, you can use trimmers anywhere — along a hard surface, in tight spaces, next to planting beds, and so on. Trimmers also leave some clippings on paths and driveways that you need to sweep up.Never put grass clippings in a plastic bag and send them off to the dump. (In some areas, sending grass clippings to the dump is illegal.) Grass clippings are valuable organic matter, chock-full of nitrogen and other nutrients. As long as you mow often enough to remove no more than one third of the grass blade, the easiest thing to do is just to leave clippings on the lawn. The pieces break down quickly and reduce the amount of fertilizer you have to use by as much as 25 percent. And research has proven that the clippings don't cause thatch to build up.Lawn mowing safety when you mow a lawnEvery year, hundreds, maybe even thousands, of people get injured when using lawn mowers. Power lawn mowers can be dangerous even when used properly. Be proactive when it comes to safety and follow these tips to avoid injuries: Know the equipment. Read the owner's manual. Become familiar with all the safety features and don't disconnect any of them. Keep all nuts and bolts properly tightened. Never pull a walking mower. Check the lawn before mowing and wear proper clothing. Pick up any rocks or debris. Heavy shoes and long pants provide the best protection from flying debris. If you're using a reel mower, don't wear loose clothing. Protect your hearing. Doing yard work can get pretty noisy. In addition to the lawn mower, high-decibel noise comes from trimmers, edgers, and blowers. Use earplugs or earmuff-type hearing protection. Keep pets and children away from the lawn as you mow. Don't let children operate a lawn mower unless they're strong enough, responsible, and understand all the operating and safety features. Even then, supervise them. Never give a young child a ride on a ride-on mower. Sudden stops, flying objects, or an excited child can spell disaster. Be careful when fueling. Stop the mower and let the engine cool for 10 minutes before fueling. Never fill the tank with the mower on the lawn. Avoid spills by using a gas can with an adequate pouring spout. Clean up spills immediately and put the used rags in a covered metal can. (Gasoline-soaked rags are a fire hazard.) Turn off the mower. Never leave the mower running unattended, or work on a motor that is running. Turn off the power when you cross nongrass areas. Be careful on hills. Steep slopes are always dangerous because a mower can flip over or go out of control. Plant a ground cover other than turf in these areas. On gentle slopes, mow across the slope, not up and down. Use a walk-behind mower. Lawn mowers — a tree's worst enemyRepeatedly banging a mower against a tree trunk or whipping it senseless with a weed whip each week can seriously damage the bark and the sensitive tissues underneath. The damage can restrict the growth of young trees to the point where the base of the trunk is so weak and girdled that the tree just snaps off in the slightest wind.To protect the tree, leave a ring of grassless soil at least 3 feet wide around the trunk. Put in a nice brick or stone edging around the outside. Better yet, cover the open soil with a thick layer (3 to 6 inches deep) of organic mulch, such as compost or bark. (Keep the mulch a few inches away from the base of the tree.) Grass type Height Bahia grass; fescue, tall; blue grama; buffalo grass 2 to 3 inches Grass type Height Bahia grass; fescue, tall; blue grama; buffalo grass 2 to 3 inches Bent grass 1/4 to 1 inch Bermuda grass, common 3/4 to 1-1/2 inches Bermuda grass, hybrid 1/2 to 1 inch Centipede grass; zoysia grass* 1 to 2 inches Fescue, fine; St. Augustine grass 1-1/2 to 2-1/2 inches Kentucky bluegrass 1-3/4 to 2-1/2 inches Ryegrass, annual and perennial 1-1/2 to 2 inches *You can mow some newer, dwarf varieties lower. Bermuda grass, common 3/4 to 1-1/2 inches Grass type Height Bahia grass; fescue, tall; blue grama; buffalo grass 2 to 3 inches Bent grass 1/4 to 1 inch Bermuda grass, common 3/4 to 1-1/2 inches Bermuda grass, hybrid 1/2 to 1 inch Centipede grass; zoysia grass* 1 to 2 inches Fescue, fine; St. Augustine grass 1-1/2 to 2-1/2 inches Kentucky bluegrass 1-3/4 to 2-1/2 inches Ryegrass, annual and perennial 1-1/2 to 2 inches *You can mow some newer, dwarf varieties lower. Bermuda grass, hybrid 1/2 to 1 inch Grass type Height Bahia grass; fescue, tall; blue grama; buffalo grass 2 to 3 inches Bent grass 1/4 to 1 inch Bermuda grass, common 3/4 to 1-1/2 inches Bermuda grass, hybrid 1/2 to 1 inch Centipede grass; zoysia grass* 1 to 2 inches Fescue, fine; St. Augustine grass 1-1/2 to 2-1/2 inches Kentucky bluegrass 1-3/4 to 2-1/2 inches Ryegrass, annual and perennial 1-1/2 to 2 inches *You can mow some newer, dwarf varieties lower. Centipede grass; zoysia grass* 1 to 2 inches Grass type Height Bahia grass; fescue, tall; blue grama; buffalo grass 2 to 3 inches Bent grass 1/4 to 1 inch Bermuda grass, common 3/4 to 1-1/2 inches Bermuda grass, hybrid 1/2 to 1 inch Centipede grass; zoysia grass* 1 to 2 inches Fescue, fine; St. Augustine grass 1-1/2 to 2-1/2 inches Kentucky bluegrass 1-3/4 to 2-1/2 inches Ryegrass, annual and perennial 1-1/2 to 2 inches *You can mow some newer, dwarf varieties lower. Fescue, fine; St. Augustine grass 1-1/2 to 2-1/2 inches Grass type Height Bahia grass; fescue, tall; blue grama; buffalo grass 2 to 3 inches Bent grass 1/4 to 1 inch Bermuda grass, common 3/4 to 1-1/2 inches Bermuda grass, hybrid 1/2 to 1 inch Centipede grass; zoysia grass* 1 to 2 inches Fescue, fine; St. Augustine grass 1-1/2 to 2-1/2 inches Kentucky bluegrass 1-3/4 to 2-1/2 inches Ryegrass, annual and perennial 1-1/2 to 2 inches *You can mow some newer, dwarf varieties lower. Kentucky bluegrass 1-3/4 to 2-1/2 inches Grass type Height Bahia grass; fescue, tall; blue grama; buffalo grass 2 to 3 inches Bent grass 1/4 to 1 inch Bermuda grass, common 3/4 to 1-1/2 inches Bermuda grass, hybrid 1/2 to 1 inch Centipede grass; zoysia grass* 1 to 2 inches Fescue, fine; St. Augustine grass 1-1/2 to 2-1/2 inches Kentucky bluegrass 1-3/4 to 2-1/2 inches Ryegrass, annual and perennial 1-1/2 to 2 inches *You can mow some newer, dwarf varieties lower. Ryegrass, annual and perennial 1-1/2 to 2 inches Grass type Height Bahia grass; fescue, tall; blue grama; buffalo grass 2 to 3 inches Bent grass 1/4 to 1 inch Bermuda grass, common 3/4 to 1-1/2 inches Bermuda grass, hybrid 1/2 to 1 inch Centipede grass; zoysia grass* 1 to 2 inches Fescue, fine; St. Augustine grass 1-1/2 to 2-1/2 inches Kentucky bluegrass 1-3/4 to 2-1/2 inches Ryegrass, annual and perennial 1-1/2 to 2 inches *You can mow some newer, dwarf varieties lower. *You can mow some newer, dwarf varieties lower. Edging and trimming are the finishing touches of mowing, kind of like getting a shave after you've had a haircut. Edging and trimming are pretty close to being the same thing. Some tools are called edgers because they're designed to trim the lawn along a hard surface like a driveway or sidewalk. Edgers cut a nice clean edge, but leave some dirt and grass debris that you need to clean up. On the other hand, you can use trimmers anywhere — along a hard surface, in tight spaces, next to planting beds, and so on. Trimmers also leave some clippings on paths and driveways that you need to sweep up. Never put grass clippings in a plastic bag and send them off to the dump. (In some areas, sending grass clippings to the dump is illegal.) Grass clippings are valuable organic matter, chock-full of nitrogen and other nutrients. As long as you mow often enough to remove no more than one third of the grass blade, the easiest thing to do is just to leave clippings on the lawn. The pieces break down quickly and reduce the amount of fertilizer you have to use by as much as 25 percent. And research has proven that the clippings don't cause thatch to build up. Lawn mowing safety when you mow a lawn Every year, hundreds, maybe even thousands, of people get injured when using lawn mowers. Power lawn mowers can be dangerous even when used properly. Be proactive when it comes to safety and follow these tips to avoid injuries: Know the equipment. Read the owner's manual. Become familiar with all the safety features and don't disconnect any of them. Keep all nuts and bolts properly tightened. Never pull a walking mower. Check the lawn before mowing and wear proper clothing. Pick up any rocks or debris. Heavy shoes and long pants provide the best protection from flying debris. If you're using a reel mower, don't wear loose clothing. Protect your hearing. Doing yard work can get pretty noisy. In addition to the lawn mower, high-decibel noise comes from trimmers, edgers, and blowers. Use earplugs or earmuff-type hearing protection. Keep pets and children away from the lawn as you mow. Don't let children operate a lawn mower unless they're strong enough, responsible, and understand all the operating and safety features. Even then, supervise them. Never give a young child a ride on a ride-on mower. Sudden stops, flying objects, or an excited child can spell disaster. Be careful when fueling. Stop the mower and let the engine cool for 10 minutes before fueling. Never fill the tank with the mower on the lawn. Avoid spills by using a gas can with an adequate pouring spout. Clean up spills immediately and put the used rags in a covered metal can. (Gasoline-soaked rags are a fire hazard.) Turn off the mower. Never leave the mower running unattended, or work on a motor that is running. Turn off the power when you cross nongrass areas. Be careful on hills. Steep slopes are always dangerous because a mower can flip over or go out of control. Plant a ground cover other than turf in these areas. On gentle slopes, mow across the slope, not up and down. Use a walk-behind mower. Lawn mowers — a tree's worst enemy Repeatedly banging a mower against a tree trunk or whipping it senseless with a weed whip each week can seriously damage the bark and the sensitive tissues underneath. The damage can restrict the growth of young trees to the point where the base of the trunk is so weak and girdled that the tree just snaps off in the slightest wind. To protect the tree, leave a ring of grassless soil at least 3 feet wide around the trunk. Put in a nice brick or stone edging around the outside. Better yet, cover the open soil with a thick layer (3 to 6 inches deep) of organic mulch, such as compost or bark. (Keep the mulch a few inches away from the base of the tree.) You can also go to a garden center to buy trunk protectors, plastic sleeves that encircle the trunk, if you have to have the grass right up against the tree. View Article

Lawn Care Replacing Powered Lawn Tools with Eco-Friendly Alternatives Article / Updated 12-14-2022 Tool sheds and garages can harbor some of the least green garden products on the market. In addition to chemicals for killing weeds and pests, you’re likely to find fossil-fuel-burning gas-powered lawn mowers and electric tools. Cut down the energy you use in the garden by replacing your power tools with manual alternatives: WordStr an electric or gas lawn mower with a push reel mower, also known as a hand mower. WordStr an electric lawn edger with a foot-powered lawn edger. WordStr an electric trimmer with long-necked grass shears. WordStr an electric or gas chainsaw with a manual pocket chainsaw. WordStr an electric or gas leaf blower with a garden rake. Sure, being green in the garden involves more manual labor and elbow grease, but think of all the energy and pollution you’re saving! You can also opt for cordless electric or solar-powered alternatives for items such as lawn mowers; they have the best of both worlds: reducing emissions and saving labor. You should find an increasing selection of cordless electric or solar-powered tools wherever conventional lawn mowers and other garden machines are sold. If your lawn is too large to tackle with a push reel mower, get a battery-powered mower that charges using solar power, or use green electricity, which is generated by renewable sources such as wind, solar, or hydro power. View Article

Lawn Care How to Lay Sod for a New Lawn Step by Step / Updated 03-27-2016 Laying sod is a gratifying experience—you get a new, green lawn in no time! The time to lay sod is early morning before it gets too hot. The soil in the planting area should be moist, not soggy or dry. Water thoroughly one or two days before the sod is delivered so that the top several inches of soil are wetted. Then allow time for the soil to drain so that it’s not muddy and is workable. View Step by Step

Lawn Care Keeping an Eco-Friendly Lawn Article / Updated 03-26-2016 If your yard includes some lawn and you aren’t yet ready to replace it with more sustainable alternatives, make your grass as green as possible by using eco-friendly, toxic-free methods to keep it healthy. Follow these suggestions: Use native grass seeds. They’ll grow better in your local climate than other varieties. Leave grass cuttings on the lawn to feed the soil. If there are too many cuttings, put the excess in the compost heap. If your lawn turned brown in the sun the last time you cut it, let the grass grow a little longer between cuttings and don’t cut it so short next time. Longer grass (2-1/2 to 3-1/2 inches, depending on the grass variety) stays greener than a close-mown lawn, is less likely to scorch, and needs less watering. Leave some of the lawn to grow wild with flowers and decorative grasses, or plant some trees and shrubs. Those areas will attract wildlife and reduce the amount of effort needed to care for the lawn. View Article

Lawn Care Choosing a Warm-Season Grass Article / Updated 03-26-2016 If you live in a warm climate, you should choose from among these commonly used warm-season grasses: Bahia grass, common and hybrid Bermuda grass, centipede grass, St. Augustine grass, and zoysia grass. Whether you live in Florida or California, chances are that your lawn has one or a combination of these grasses growing in it: Bahia grass: Bahia grass (Paspalum notatum) is a tough, coarse grass that roots deeply and extensively. This grass sends out runners that can help stabilize erosion-prone soil. Bahia grass is low-growing and forms a tough, open turf that resists thatch. Bahia grass has excellent wearability, but gets a high-maintenance rating in the mowing department. You need to mow frequently with sharp blades. Bahia grasses are shade-tolerant, moderately drought-tolerant, and do well in sandy or infertile soils of the southern coastal plains of the United States. These grasses stay green longer than most of the warm-season grasses over the winter months. Bermuda grasses: You can choose from two Bermuda grasses: Common Bermuda grass: Common Bermuda grass (Cynodon dactylon) is a medium green, medium- to fine-textured turf. The grass roots deeply and spreads quickly, making it heat- and drought-tolerant. The rapid spreading can cause a problem of invasion into unwanted areas if not kept in check. This turf has excellent wearability, however, it doesn’t do well in shade and turns brown in winter until daytime temperatures reach a consistent 60 degrees F. Common Bermuda grass grows well in poor soils. Hybrid Bermuda grass: The hybrid Bermuda grasses (Cynodon dactylon crossed with C. transvaalensis) are softer, denser, greener, and more finely textured than the common Bermuda grasses. Hybrid Bermuda grass is heat-loving, fast-growing, drought-tolerant, and very durable, making it a good choice for high-traffic lawns. The hybrid types are more disease- and pest-resistant than common Bermuda grass, but thatch buildup can become a problem. Centipede grass: Centipede grass (Eremochloa ophiuroides) is a medium- to fine-textured, light green grass that spreads by creeping stolons. This grass has shallow roots, making it only moderately tolerant to drought, slow to fill in as a lawn, and slow to recover from wear and tear. Centipede grass is not a high-traffic-area grass. However its good resistance to disease and pests make it a good, low-maintenance lawn grass. It’s one of the first of the warm-season grasses to turn brown in hot, dry weather and to go dormant with the arrival of winter. This grass tolerates moderate shade, but doesn’t tolerate the salt from sea spray. Centipede grass can turn yellow in alkaline soils that lack iron, but greens up with applications of iron sulphate or iron chelate. St. Augustine grass: St. Augustine grass (Stenotaphrum secundatum) is a fast-growing, deep-rooted, coarse to medium-textured grass with broad, dark green leaves. The grass spreads rapidly by surface runners that form a thick, dense turf, giving this grass an A for wearability. This grass is quite popular in southern climates, from Florida to California, because of its tolerance to heat, sun, shade, and salt. St. Augustine grass can grow in most soils, but prefers well-fertilized, well-drained, alkaline soil. St. Augustine grass is susceptible to brown patch, mole crickets, sod webworm, chinch bugs, and a virus called St. Augustine Decline (SAD, for short). Zoysia grass: Zoysia grasses are fine- to medium-textured, dark green, and moderately deep rooted. The blades are wiry, making them the least comfortable lawn for barefooted traffic. You generally plant zoysias by plugs, which may take two seasons to fill in your lawn space. However, when the plugs spread out and the space gets covered, you end up with a fairly low-maintenance lawn that can withstand high traffic. When properly cared for, zoysias are fairly pest- and disease-resistant when compared to other warm-season grasses. However, brown patch, dollar spot, armyworms, billbugs, and sod webworms can occasionally create problems if you slack off on maintenance. Ditto thatch. The Native Grasses: North America’s native American grasses are growing in popularity among more environmentally conscious lawn lovers because of their lack of demands on precious resources and labor. For the most part, native grasses need little water once established, very little fertilizer, and a haircut only a few times a year. The two most popular warm-season native grasses are blue grama and buffalo grass: Blue grama: Although this grass goes dormant, it tolerates extreme heat and cold and does well in the arid regions of the Central Plains. Blue grama is very drought-tolerant and offers moderate wearability, but is slow to recover from wear damage. Buffalo grass: Buffalo grass is drought-tolerant once established and becomes even more so if mowed infrequently and high. This grass thrives in areas that receive only 10 to 15 inches of rain a year, but will go brown if allowed to go completely dry. More lawnlike in appearance than other natives, buffalo grass is becoming quite popular in drought-prone regions. However, it’s expensive to plant, whether by seed, sod, or plug. View Article

Lawn Care Connecting a Lawn Irrigation System to a Home Water Supply Article / Updated 03-26-2016 Connecting your lawn irrigation system to the plumbing system in your house is one of the final steps of installation. The water for your lawn irrigation system has to come from somewhere, so you need to hook your system to the house water supply. Tapping into the water supply is one part of the installation that you should really get help on from a professional installer or plumber. Making a mistake with your plumbing system can be expensive when you have to call in the professionals to fix it. First, turn off the main water supply to the house unless you want to have a huge gigantic gusher of a mess. The kids may like it, but you won’t. The following list shows three ways to tap into the water supply: Tap the outside faucet. Unscrew the outside faucet and install a 1-inch galvanized or copper tee fitting facing down. Screw the faucet back on to the tee. Below the tee, install a shutoff valve and then run pipe to the manifold and your irrigation system. This is probably the least complicated junction. Tapping the main line. Cut a section out of your main line and install a compression tee fitting. Run the pipe a few inches away and install a shutoff valve. Then run pipe to your manifold. Tapping the basement water meter. Just past the water meter, cut into the line and install a compression tee. From there, run a short line and install a shutoff valve. Run pipe up to the trench level outside and drill a hole through the basement wall. Run pipe out to the manifold. The manifold is a grouping of control valves that connects the water source to the system and controls the flow of water to each circuit. Following your manufacturer’s instructions, attach the various pipes to the control valves at the manifold by using pipe tape (white tape that you wrap around the treads to prevent the connection from leaking). Attach the pipes carefully — not so tight that you damage the threads and cause the pipes to leak. After you have the entire irrigation system attached to the manifold and the main water line, you’re heading down the stretch to the finish line. Attach the risers. Cut the pipe at each spot where a riser is to go and install a tee fitting. Install the riser, making sure that the sprinkler head will be at or just above soil level. If you’ll be planting sod, the heads need to be an inch or so higher than soil level to accommodate the thickness of the sod. A number of flexible or adjustable risers make this connection easy. Flush the system. To do so, turn on the main water line and then the irrigation system and flush out the pipes for a few minutes. Sprinkler heads can clog very easily, and you want to eliminate all dirt in the lines. Turn off the water. Bring on the sprinkler heads. Screw the sprinkler heads on to the risers, making sure that they’re adjusted correctly and pointing in the right directions. Install a controller or timing device (optional). If you’re going to install a controller or timing device, now is the time. This electrical device should be in a protected place not far from your power source. A heated garage or basement is good. Be sure to run the electrical wires to connect the controller to the manifold in a waterproof pipe. The controller should be buried to protect it from rain and freezing weather. Test your system. If all the pipes and fittings are not leaking, you can backfill the trenches. If you installed the system in an existing lawn, replant the open soil with seed or sod. Otherwise, you’re ready to do some final leveling and plant your new lawn. View Article

Lawn Care How to Aerate Your Lawn Article / Updated 03-26-2016 Aerating is the process of punching small holes all over your lawn. The most effective type of aerating is with a gas-powered machine called a core aerator that pulls out small cores of grass and soil. Other aerators use short spikes to punch holes in the turf. Spiking is not nearly as effective as core aerating, but it’s better than nothing. Aerating does exactly what it sounds like and more. Air is critical to healthy root growth, so it shouldn’t surprise you that aerating is a good thing. Aerating your lawn breaks through a thatch layer, enables the roots to breathe, and improves water and nutrient penetration. If that’s not enough, aerating helps break down thatch by providing a better habitat for the microorganisms that do those sorts of things. Aerating annually is one of the best things you can do for your lawn, thatch or no thatch. Aerating is not nearly as traumatic as dethatching. You end up with some little cores of soil all over the lawn, but if those really bother you, you can rake them up. If you leave the cores alone, they break down into nothing in a few weeks anyway. So compared to dethatching, which can pulverize a lawn, aerating leaves the lawn in pretty good shape. Consequently, if you have a small thatch problem, aerating once a year probably solves the problem. Signs that your lawn needs to be aerated include Worn areas where people walk often Water puddles after irrigating Water runs off the lawn after only a few minutes of watering Parts of the lawn that just can’t seem to keep moist When you aerate, strive for an even 3- to 4-inch spacing between holes throughout the lawn. To do so, you must make two passes in different directions. Make sure that the soil is slightly moist — not too wet or too dry. Set the aerator to pull out cores about 3 inches long. Years of walking on a lawn or driving heavy equipment on it during construction can compact soil, smashing the particles tightly together and forcing all the air out. You got it: No air, bad for roots. You can identify the compacted areas because that’s where the water always puddles up. Eventually, the grass declines and starts turning brown because the roots receive no air, and water can’t get to them either. Compaction is particularly troublesome where soils are heavy clay. In fact, clay soil can have poor aeration and be slow to absorb water without your help. Walk all over clay soil, especially when soggy, and you really have problems. So what’s the answer for compacted or clay soil? You got it. Aerate. Aerating provides air to the roots and improves water penetration. More air and water mean happier roots and a healthier lawn. If your area has clay soil, you may want to aerate at least once a year. Oh, and one other place where aerating really helps is on sloping ground where water runs off quickly before it can soak in. Aerate, and more water can reach the roots. Is aerating great or what? View Article

Lawn Care How to Calibrate a Broadcast Spreader Article / Updated 03-26-2016 A broadcast spreader is more difficult to calibrate than a drop spreader is because you can’t catch the fertilizer as it’s being thrown out. Broadcast spreaders throw fertilizer over a wide area of your lawn and are particularly useful for large lawns. To use a broadcast spreader properly, you need to know how wide a band the spreader covers. If the directions that came with the spreader don’t indicate the width, put some fertilizer in the spreader and run the spreader over a short stretch of lawn to find out. Don’t measure the coverage on concrete unless you plan to sweep up the fertilizer This type of spreader comes in handheld or wheeled models. The manufacturer presets a new spreader to apply fertilizers at specific rates according to the amount of nitrogen needed per 1,000 square feet. As the spreader gets older, these settings can get out of whack and not apply the proper amount. You also may find that the spreader doesn’t have a specific setting for the type of fertilizer you’re using. In either case, calibrating a spreader can tell you exactly how much fertilizer you’re applying and whether you need to make any adjustments. Calibrating your spreader every year or two is a good idea. Take the following steps to calibrate a broadcast spreader. Weigh out an amount of fertilizer to cover a specific size test area — for example, enough for a 200-square-foot area (1/5 of 1,000 square feet). For example, if you’re using a fertilizer with 29 percent nitrogen, you need 3.4 pounds of fertilizer for 1,000 square feet. Divide 3.4 by 5 (roughly 0.7 pounds) to get the amount needed for 200 square feet. Mark a starting point and then push the spreader several feet to measure the width over which the fertilizer is effectively spread. Calculate and mark off a 200-square-foot area from the original starting point. For example, if your spreader throws out a 10-foot effective width, mark off a total of 20 feet (10 ´ 20 = 200 square feet) and complete spreading the fertilizer over 200 square feet. Increase the setting number if there is still fertilizer in the hopper. If you ran out of fertilizer before finishing, close down the setting. When you have an accurate setting, record the number for future use. Another point to remember is to calibrate the spreader over the lawn area, not on the driveway or street. Not only are you wasting money, the fertilizer will be washed into storm drains or creeks and other water systems. If you calibrate your spreader on the driveway, be sure to sweep up all the fertilizer when you finish. A driveway calibration shows exactly what the patterns are, and you don’t end up with a dark, ugly green or burned spot on the lawn if that’s where the spreader was calibrated. View Article

Lawn Care How to Choose an Efficient Lawn Sprinkler Article / Updated 03-26-2016 Choosing the right lawn sprinkler is one of the most important decisions you can make if you want a healthy lawn without wasting water. Sprinklers are either portable or fixed: Portable sprinklers: Portable sprinklers come in myriad styles with varying application rates (how fast they apply water) and application patterns (covering square, round, or rectangular areas). Portable sprinklers also vary by how large an area you can cover, but that area is further influenced by how high you turn on the hose and the amount of water pressure. Portable sprinklers vary in price from very inexpensive to quite costly. The main disadvantage of portable sprinklers is that you need to move them around by hand. On large lawns, this task can be a real chore. Another problem with portable sprinklers is uneven distribution of water within the sprinkler pattern. After you choose a sprinkler, perform the trusty can test, so that you know how long to run the sprinklers and how you need to overlap the patterns to provide complete coverage. Place cans around the lawn to see how the water is distributed. Permanent sprinklers: Permanent, in-ground sprinkler systems have many advantages over portable sprinklers and are really the best choice where summers are dry or where lawns are large. Here’s how the advantages stack up: You can connect permanent sprinklers to timers and fully automate them. You can precisely design placement so that all parts of the lawn are watered evenly without runoff. You can hook up permanent sprinklers to soil moisture sensors so that the lawn is watered only when needed. You can connect permanent sprinklers to rain sensors so that they automatically shut off when it rains. Permanent sprinklers offer more flexibility in terms of application rates, uniform distribution of water, and spray patterns. Of course, the main disadvantage to permanent irrigation systems is their cost and the labor involved in installing them. The ideal time to install a permanent irrigation system is when you plant a lawn. Still, you can dig up some grass and install in-ground sprinklers anytime. Even if you have a fully automated irrigation system, you’re not off the lawn-watering hook forever. You still have to keep an eye on the system to make sure that it operates properly. You have to adjust the timer with the seasons and maybe even turn it off in winter. And remember: Apply less water when the weather is cooler, more when it’s hot. Do you turn the sprinklers on and forget about them for two hours, and then find out you’ve nearly washed away the entire neighborhood? Buy an inexpensive timer that hooks up between your faucet and your hose. Set it for the appropriate time, and the timer shuts off the sprinklers for you. It can also water your lawn while you’re on vacation. The one most important piece of advice about hoses is this: Don’t buy a cheap hose. Spend a little money and buy one made of high-grade rubber, laminated filament, or other quality material. Buy a hose that rolls up easily in any weather and doesn’t kink. Cheap hoses are a curse! View Article